Below two steps for you to follow up with assemble the mini titan heli and start to learn the hovering from Simulator.
A. Assemble the heli  and B. learn from Simulator.

A. Assemble the heli
Remove the heli and  tail assembly from the card broad. Follow by remove the masking tape at the belt.
Refer to mini Titan assemble manual page 26 for the rest of the tail assembly instruction
Refer to mini Titan assemble manual page 32 How to assemble the main rotor blade.

Connection of the receiver and control
Place the TG6100 wire to the receiver.
Black, red, white color wire connect to Channel 1
Single red color wire connect to channel 2
Single orange wire connect to channel 3
Single yellow wire connect to channel 4
Please ignore the green and blue wire connector.
Lastly tail servo wire plug to TG6100 Rudder and lay out your receiver wire accordingly to

Transmitter manual
Turn to the back of the transmitter and open the battery cover
You will find four switch after your open the battery cover.
Reverse the channel 2 ( indicated at REV)
Left the rest to normal position. ( indicated at NOR)
Charging up the transmitter battery, it take at less 8-12 hrs to full charge the battery.

Switch on the transmitter and make sure all the sub trim are at central position. (NOTE: rudder sub trim have to be at center as the TG6100 it is a head lock gyro, if out of center, head lock function will no work!)
Lower down the throttle stick
Connect the lipo battery to the helicopter BLC
Now check the swashplate is all in level as refer to manual page 39, you may need to adjust the link rod from servo link to swashplate if it is out of lever..
You might up trim the throttle position to high and start to fly by increase the throttle stick.

**Very Important, the 2808 3S1P Lithium polymer battery it can not be over discharge, once the heli loss power, you need to stop and re-charge the lipo battery again.


Fly your helicopter is not quite as simple as it looks. We have all seen the pilots when were newbie and thought that looks simple. Then you try it on your own remote control helicopter and find out to your frustration, that it is not simple after all. Follow these guidelines and we hope you will be up in the air and in control in no time. Before we start. These are great tips for all newbie’s and we recommend that you read them as well.

B. learn from Simulator.
Following these guidelines when using a simulator will not only improve your performance in real life. It also familiarized you with the characteristics of RC flight. Just download the software from this link.  http://www.rotor.com.sg/fms/

Following the instructions in the website for installment and start up of the software.

Hovering Lesions

Stage One (Tail in Hovering)

Lift the helicopter up from the heli pad with its tail facing you and try to control the helicopter within the heli pad.

*Don't let the helicopter hit you nor getting it fly too far away.

Stage Two (landing)

Ok, after you can control the helicopter within the pad. Now u has to learn landing which means to land the heliport in the heli pad safely without crushing. After this you can make the helicopter land wherever you want it to.

Stage Three (side way hovering)

Now turn your helicopter with either its left or right side facing you. Try to control the helicopter within the pad again. You have to learn the both side left and right side way hovering.

Stage Four (side way landing)

Now you have to land the helicopter safely back to the pad. Land your helicopter with either left or right side facing you. You have to learn the both side left and right side way landing.

Stage Five (nose in hovering)

Lift the helicopter up with the nose facing you and try to control the helicopter within the pad.

Stage Six (nose in landing)

Land your helicopter safely back to the pad with the nose facing you.
Congratulation! You have master all the hovering that you need to learn.

you also can see more demo flying at youtube on following web address:

http://www.youtube.com/watch?v=lkkxBKjTkzQ

INFO by http://shop.rotor.com.sg/